|
|
Part: JANKCB2N2484
Category:
Description: Semiconductor Device, Transistor, Npn, Silicon, Low-power Types 2n2484, 2n2484ua, 2n2484ub, Jan, Jantx, Jantxv, Jans, Janhc, And Jankc
Company: ST Microelectronics, Inc.
Datasheet: Download JANKCB2N2484 datasheet File size : 84 kB
Request For quote: Find where to buy JANKCB2N2484
Datasheet text preview:
The documentation and process conversion measures necessary to comply with this revision shall be completed by 31 November 2000.
INCH-POUND MIL-PRF-19500/376E 31 August 2000 SUPERSEDING MIL-PRF-19500/376D 21 August 1998 PERFORMANCE SPECIFICATION
SEMICONDUCTOR DEVICE, TRANSISTOR, NPN, SILICON, LOW-POWER TYPES 2N2484, 2N2484UA, 2N2484UB, JAN, JANTX, JANTXV, JANS, JANHC, AND JANKC This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the performance requirements for NPN, silicon, low-power transistors. Four levels of product assurance is provided for each device type as specified in MIL-PRF-19500. Two levels of product assurance are provided for die. 1.2 Physical dimensions. See figure 1 (similar to T0-18), figures 2 and 3 (surface mount case outlines UA and UB), and figures 4 and 5 (die). 1.3 Maximum ratings.
Types
PT TA = +25°C
VCBO
VEBO
VCEO
IC
TJ and TSTG
RJA
R J C
mW 2N2484 2N2484UA 2N2484UB 500 (1) 650 (2) 500 (1)
V dc 60 60 60
V dc 6 6 6
V dc 60 60 60
mA dc 50 50 50
°C -65 to +200 -65 to +200 -65 to +200
°C/W 325 210 325
°C/W 146 160 146
(1) Derate linearly at 3.08 mW/°C above TA = +37.5°C (2) Derate linearly at 4.76 mW/°C above TA = +63.5°C. 1.4 Primary electrical characteristics.
hfe Limits VCE = 5 V dc IC = 1 mA dc f = 1 kHz Cobo IE = 0 VCB = 5 V dc 100 kHz f 1 MHz pF Min Max 250 900 2.0 7.0 |hfe|2 IC = 500 µA dc VCE = 5 V dc f = 30 MHz VCE(sat) (1) IC = 1.0 mA dc IB = 0.1 mA dc
V dc
5.0
0.3
(1) Pulsed (see 4.5.1). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC/VAC, Post Office Box 3990, Columbus, OH 43216-5000, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. FSC 5961
MIL-PRF-19500/376E
Symbol CD CH HD LC LD LL LU L1 L2 Q TL TW r
Dimensions Inches Millimeters Min Max Min Max .178 .195 4.52 4.95 .170 .210 4.32 5.33 .209 .230 5.31 5.84 .100 TP 2.54 TP .016 .021 0.41 0.53 .500 .750 12.7 19.05 0 .016 .019 0.41 0.48 --.050 --1.27 .250 --6.35 ----.040 --0.86 .028 .048 0.71 1.22 .036 .046 0.91 1.17 --.010 --0.25 45° TP 45° TP
Note
6 7,8 7,8 7,8 7,8 7,8 5 3,4 3 10 6
NOTES: 1. Dimension are in inches. 2. Metric equivalents are given for general information only. 3. Beyond r (radius) maximum, TW shall be held for a minimum length of .011 (0.28 mm). 4. Dimension TL measured from maximum HD. 5. Body contour optional within zone defined by HD, CD, and Q. 6. Leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shall be within .007 inch (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. 7. Dimension LU applies between L1 and L2. Dimension LD applies between L2 and LL minimum. Diameter is uncontrolled in L1 and beyond LL minimum. 8. All three leads. 9. The collector shall be internally connected to the case. 10. Dimension r (radius) applies to both inside corners of tab. 11. In accordance with ANSI Y14.5M, diameters are equivalent to x symbology. 12. Lead 1 = emitter, lead 2 = base, lead 3 = collector.
FIGURE 1. Physical dimensions (similar to TO-18).
2
MIL-PRF-19500/376E
Symbol A A1 B1 B2 B3 D D1 D2 D3 E E3 L1 L2 L3
Dimensions Inches Millimeters Min Max Min Max .061 .075 1.55 1.90 .029 .041 0.74 1.04 .022 .028 0.56 0.71 .075 REF 1.91 REF .006 .022 0.15 0.56 .145 .155 3.68 3.93 .045 .055 1.14 1.39 .0375 BSC .952 BSC --.155 --3.93 .215 .225 5.46 5.71 --.225 --5.71 .032 .048 0.81 1.22 .072 .088 1.83 2.23 .003 .007 0.08 0.18
Note 3
5
5
NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Dimension "A" controls the overall package thickness. When a window lid is used, dimension "A" must increase by a minimum of .010 inch (0.254 mm) and a maximum of .040 inch (1.020 mm). 4. The corner shape (square, notch, radius, etc.) may vary at the manufacturer's option, from that shown on the drawing. 5. Dimensions "B3" minimum and "L3" minimum and the appropriately castellation length define an unobstructed three-dimensional space traversing all of the ceramic layers in which a castellation was designed. (Castellations are required on bottom two layers, optional on top ceramic layer.) Dimension "B3" maximum and "L3" maximum define the maximum width and depth of the castellation at any point on its surface. Measurement of these dimensions may be made prior to solder dipping. 6. Lead 4 = no connection. FIGURE 2. Physical dimensions, surface mount (2N2484UA).
3
Others parts begin by ja
JA-1 JA-2 JA-3 JA-4 JA-5 JA-6 JA-7 JA-8 JA-9 JA-10 JA-11 JA-12 JA-13 JA-14 JA-15 JA-16 JA-17 JA-18 JA-19 JA-20 JA-21 JA-22 JA-23 JA-24 JA-25 JA-26 JA-27 JA-28 JA-29 JA-30 JA-31 JA-32 JA-33 JA-34 JA-35 JA-36 JA-37 JA-38 JA-39 JA-40 JA-41 JA-42 JA-43 JA-44 JA-45 JA-46 JA-47 JA-48
|
|
|
