|
|
Part: PC354
Category:
Description: Device Specification For Photocoupler
Company: Sharp Microelectronics of the Americas
Datasheet: Download PC354 datasheet File size : 71 kB
Request For quote: Find where to buy PC354
Datasheet text preview:
PREPARED
BY:
DATE:
SHA
DATE: ELECTRONIC COMPO GROUP SHARP CORPORATION
I SPEC.
No.
ED-9466 October
1B 29. 1999
APPROVED
BY:
SPECIFICATION
DEVICE SPECIFICATION No. FOR
I
I I
OF'TO-ELECT=
I
PHOTOCOUPLER
MODEL
Business
dealing
name
PC354
(`Sharp").
1. These speciilcation sheets include materials protected under copyright of Sharp Corporation Please do not reproduce or cause anyone to reproduce them without Sharp's consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets, and the precautions mentioned below. (Precautions) (1) This product is designed for use in the following application areas : Audio visual equipment OA equipment * Home appliances . Telecommunication equipment (Terminal) * Measuring equipment Computers 1 Tooling machines If the use of the product in the above application areas is for equipment listed in paragraphs (21 or (31, please be sure to observe the precautions given in those respective paragraphs.
l l l l
1
(21 Appropriate measures, such as fail-safe design and redundant design considering the safety design of the overall system and equipment, should be taken to ensure reliability and safety when this product is used for equipment which demands high reliability and safety in function and precision, such as ; * Transportation control and safety equipment (aircraft, train, automobile etc.) * Tram signals * Gas leakage sensor breakers * Rescue and security equipment Other safety equipment [
l
(31 Please do not use this product for equipment which require extremely high reliability and safety in function and precision, such as : * Space equipment * Telecommunication equipment (for trunk lines) * Nuclear power control equipment * Medical equipment [ (4) Please contact and consult with a Sharp sales representative regarding interpretation of the above three paragraphs. 3. Please contact and consult with a Sharp sales representative if there are any questions
1
1
for any questions DATE PRESENTED BY
about this product.
CUSTOMERS
APPROVAL
;(i
4 of
DATE BY
K. Hachimura. Department General Manager Engineering Dept. ,I1 Opto-Electronic Devices Div. ELECOM Group SHARP CORPORATION
SHARP CORPORATION
ED-94(
1. Application This specification applies Model No. PC354. to the outline and characteristics of p
2. Outline Refer to the attached drawing No. CY6488KO2.
3. Ratings
and characteristics sheet, page 4 to 6.
Refer to the attached
4. Reliability Refer to the attached sheet, page 7.
5.
Incoming
inspection sheet, page 8.
Refer to the attached
6. Supplement 6.1 Isolation voltage shall be measured in the following method. side and between shall be used.
(1) Short between anode and cathode on the primary collector and emitter on the secondary side. (2) The dielectric withstand tester voltage with zero-cross
circuit
(3) The wave form of applied 6.2 Packaging specifications
shall be a sine wave.
SHARPCORPORATION
6.3 Collector current (Ic) Delivery rank table ("0" mark : indicates business dealing name of ordered Rank at delivery 8 Business dealing name PC354NT PC354N 1T Rank mark A or no mark A
product) Test conditions I,=+ 1mA V ca=5v Ta=25C
Ic b-M 0.2 to 4.0 0.5 to 1.5
6.4 This Model is approved Approved Model
by UL.
No. : PC354
UL file No. : E64380 6.5 This product 6.6 This product This product This product 6.7 ODS materials This product shall not contain the following materials. Also, the following materials shall not be used in the production for this product. Materials for ODS : CFC,, Halon. Carbon 1.1.1 -Trichloroethane tetrachloride. (Methylchloroform) process is AC input type. against irradiation. input and output. diode.
is not designed is operated incorporates
with electrical non-coherent
light emitting
6.8 Brominated
flame retardants such as the PBBO, and PBB, are not used
Speciiic brominated flame retardants in this device at all.
7. Notes Refer to the attached sheet- 1- 1, 2.
Others parts begin by pc
PC-1 PC-2 PC-3 PC-4 PC-5 PC-6 PC-7 PC-8 PC-9 PC-10 PC-11 PC-12 PC-13 PC-14 PC-15 PC-16 PC-17 PC-18 PC-19 PC-20 PC-21
|
|
|
