|
|
Part: EE-SA407-P2
Category:
Optoelectronics
-> Photosensors
-> Photomicrosensor
Description: EE-SA407-P2 Non-amplified Photomicrosensordata Sheet
Company: Omron Corporation
Datasheet: Download EE-SA407-P2 datasheet File size : 42 kB
Request For quote: Find where to buy EE-SA407-P2
Datasheet text preview:
EE-SA407-P2
Dimensions
Note: All units are in millimeters unless otherwise indicated.
Photomicrosensor
Features
· · · · · ·
An actuator can be attached. Snap-in mounting model. Mounts to 1.0-, 1.2- and 1.6-mm-thick panels. High resolution with a 0.5-mm-wide sensing aperture. With a 3.6-mm-wide slot.
(Actuator Mounted)
175489-3 (Tyco Electronics AMP) 0.5 (Aperture width) 2.2
+0.1 0 dia.
Photo IC output signals directly connect with logic circuit and TTL.
Optical axis
· Connects to Tyco Electronics AMP's CT-series connectors.
Absolute Maximum Ratings (Ta = 25°C)
Item
(see note)
Symbol VCC VOUT IOUT POUT Topr Tstg Tsol
Rated value 7V 28 V 16 mA 250 mW (see note) -- 20°C to 75°C -- 40°C to 85°C ---
Power supply voltage Output voltage Output current Permissible output dissipation Ambient temperature Operating Storage Soldering temperature Note:
Note: Internal Circuit
V 0 G
The dimension is specified by datum A only.
Unless otherwise specified, the tolerances are as shown below. Dimensions 3 mm max. 3 < mm 6 6 < mm 10 10 < mm 18 18 < mm 30 Tolerance ±0.3 ±0.375 ±0.45 ±0.55 ±0.65
Terminal No. V O G
Name Power supply (Vcc) Output (OUT) Ground (GND)
Refer to the temperature rating chart if the ambient temperature exceeds 25°C.
Recommended Mating Connectors: Tyco Electronics AMP 179228-3 (crimp-type connector) 175778-3 (crimp-type connector) 173977-3 (press-fit connector)
Ordering Information
Description Photomicrosensor (Actuator mounted) EE-SA407-P2 Part number
Electrical and Optical Characteristics (Ta = 25°C, VCC = 5 V ±10%)
Item Current consumption Low-level output voltage High-level output voltage Response frequency Note: Symbol ICC VOL VOH f 30 mA max. 0.35 V max. (VCC x 0.9) V min. 3 kHz min. Value Condition With and without incident IOUT = 16 mA with incident VOUT = VCC without incident, RL = 47 k VOUT = VCC, RL = 47 k (see note)
The value of the response frequency is measured by rotating the disk as shown below.
Disk
2.1 m m 0.5 m m
0.5 m m t = 0.2 mm
EE-SA407-P2 Engineering Data
Output Allowable Dissipation vs. Ambient Temperature Characteristics
Output allowable dissipation Pc (mW)
EE-SA407-P2
Sensing Position Characteristics (Typical)
d1 = 0±0.3 mm VCC = 5 V Ta = 25°C RL = 47 k
Output transistor
Center of optical axis
Ambient temperature Ta (°C)
Distance d (mm)
Recommended Mounting Holes
Light interrupting plate
17.1 ± 0.1 (for t = 1.0,1.2,1.6)
t = 1.0 mm
t = 1.2 mm
t = 1.6 mm
· When mounting the Photomicrosensor to a panel with a hole
opened by pressing, make sure that the hole has no burrs. The mounting strength of the Photomicrosensor will decrease if the hole has burrs. opened by pressing, be sure to mount the Photomicrosensor on the pressing side of the panel.
· When mounting the Photomicrosensor to a panel with a hole · The mounting strength of the Photomicrosensor will increase if
decrease if the Photomicrosensor is mounted to a panel with a hole that is comparatively larger than the size of the Photomicrosensor, in which case, however, it will be easy to mount the Photomicrosensor to the panel. When mounting the Photomicrosensor to a panel, open an appropriate hole for the Photomicrosensor according to the application.
· After mounting the Photomicrosensor to any panel, make sure
that the Photomicrosensor does not wobble.
the Photomicrosensor is mounted to a panel with a hole that is only a little larger than the size of the Photomicrosensor, in which case, however, it will be difficult to mount the Photomicrosensor to the panel. The mounting strength of the Photomicrosensor will
3
0 -- 0.2 dia.
· When mounting the Photomicrosensor to a molding with a hole,
make sure that the edges of the hole are sharp enough, otherwise the Photomicrosensor may come fall out.
Actuator Dimensions
2±0.1 dia.
Note:
1. Make sure that the portions marked with dotted lines have no burrs. 2. The material of the actuator must be selected by considering the infrared permeability of the actuator.
NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4.
R
OMRON ELECTRONICS LLC
One East Commerce Drive Schaumburg, IL 60173
OMRON CANADA, INC.
885 Milner Avenue Toronto, Ontario M1B 5V8
OMRON ONLINE
Global http://www.omron.com USA http://www.omron.com/oei Canada http://www.omron.com/oci Printed in U.S.A.
8478822288
Cat. No. GC NAPMS1 02/03
416-286-6465
Specifications subject to change without notice.
Others parts begin by ee
EE-1 EE-2 EE-3
|
|
|
