|
|
Part: EL6221CU
Category:
Description: Laser Diode Driver, 3-Channels, With 600MHz Osc, CH2/CH3=300/150mA, Enable With Oscen+outenr
Company: Intersil Corporation
Datasheet: Download EL6221CU datasheet File size : 427 kB
Request For quote: Find where to buy EL6221CU
Datasheet text preview:
®
EL6221C
3-Channel Laser Diode Driver w/Oscillator
EL6221C
®
PRODUCT BRIEF
Features
· "Shrink-small" outline package · Voltage-controlled output current source requiring one external set resistor per channel · Current-controlled output current source · CH2 to 300mA max · CH3 to 150mA max · Rise time = 0.8ns · Fall time = 0.8ns · On chip oscillator with frequency and amplitude control by use of external resistors to ground · Oscillator to 600MHz · Oscillator to 100mA pk/pk · Single +5V supply (±10%) · Disable feature for power-up protection and power savings
General Description
The EL6221C is a high performance three channel laser driver that provides controlled current to a grounded laser diode. Channels 2 and 3 should be used as the write channels, with switching speeds of approximately one nanosecond rise/fall time. All three channels are summed together at the IOUT output, allowing the user to create multilevel waveforms in order to optimize laser diode performance. The level of the output current is set by an analog voltage applied to an external resistor which converts the voltage into a current at the IIN pin (virtually ground). The current seen at this pin is then amplified to become a current source at pin IOUT. An on-chip 600MHz oscillator is provided to allow output current modulation when in any mode. This is turned on when the OSCEN pin is held high and the OUTENR pin is held low. Complete control of amplitude and frequency is set by two external resistors connected to ground at pins RFREQ and RAMP (see graphs in this datasheet for further explanation). Output current pulses are enabled when an `L' signal is applied to the OUTEN pin. No output current flows when OUTEN is `H', and additional laser diode protection is provided since the OUTEN input will float high when open. Complete IOUT shutoff is also achieved by holding the ENABLE pin low, which will override all other control pins. The external resistors allow the user to accurately and independently set each amplifier transconductance by applying a voltage to each resistor, without restriction on the voltage range, thus ensuring broad voltage DAC compatibility. Alternatively, the IIN pin can be biased from a current DAC or other current source.
Outline # MDP0040
Applications
· CD-RW applications · Writable optical drives · Laser diode current switching
Ordering Information
Part No EL6221CU Temp. Range 0°C to +70°C Package 16-Pin QSOP
Connection Diagram
1 OUTEN3 2 IIN3 3 IINR 4 RFREQ 5 IIN2 6 GND 7 OUTEN2 8 NC OUTENR 16 VCC 1 5 IOUT 14 GND 13
August 28, 2002
RAMP 12 ENABLE 11 OSCEN 10 VCC 9
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-ELANTEC or 408-945-1323 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Elantec ® is a registered trademark of Elantec Semiconductor, Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved
EL6221C
EL6221C
3-Channel Laser Diode Driver w/Oscillator
PRODUCT BRIEF
Effective May 15, 2002, Elantec, a leader in high performance analog products, is now a part of Intersil Corporation. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
®
August 28, 2002
Sales Office Headquarters
NORTH AMERICA Intersil Corporation 7585 Irvine Center Drive Suite 100 Irvine, CA 92618 TEL: 949-341-7000 FAX: 949-341-7123 Elantec 675 Trade Zone Blvd. Milpitas, CA 95035 TEL: 408-945-1323 800: 888-ELANTEC FAX: 408-945-9305 EUROPE Intersil Europe Sarl Avenue William Fraisse 3 1006 Lausanne Switzerland TEL: +41-21-6140560 FAX: +41-21-6140579 ASIA Intersil Corporation Unit 1804 18/F Guangdong Water Bldg. 83 Austin Road TST, Kowloon Hong Kong TEL: +852-2723-6339 FAX: +852-2730-1433
Printed in U.S.A.
2
Others parts begin by el
EL-1 EL-2 EL-3 EL-4 EL-5 EL-6 EL-7 EL-8 EL-9 EL-10 EL-11 EL-12 EL-13 EL-14 EL-15 EL-16 EL-17 EL-18
|
|
|
